电流监控器Currrent Monitor

电流监控器Currrent Monitor 
现在有一只西门子的电流监控器Currrent Monitor 坏了,想在224XP里用软件来实现该电流监控器Currrent Monitor 的功能,该电流监控器Currrent Monitor 功能描述如下,用软件在224XP里该如何实现该功能呢?
SIEMENS 3UG3522-1AL20
8A/250V 50/60Hz 1/3HP 1-Phase Monitoring Relay - Due to the ON-delay T2, current peaks (OVER function) or current drops (UNDER function), which may occur during closing, do not result in a change to the relay state, for example suppression of the starting current during motor acceleration. The delay time T1 prevents the relay from picking up and releasing - A green LED signalizes the applied supply voltage. A yellow LED indicates the relay status. Current monitoring without memory (NO MEMORY) (Fig. IIIa) When the value of the monitored alternating or direct current has reached the threshold set at the front panel, and the set delay time T1 has elapsed, the output relay releases. As soon as the current reaches the hysteresis value, the relay picks up again. Current monitoring with memory: (Fig. IIIb) When the set threshold value has been reached and the set delay time T1 has elapsed, the output relay releases and remains in this state, even when the measured current reaches the set hysteresis value again. A reset is performed by switching the supply voltage off and on. 23mm wide 78mm tall 104mm OAD - 4 controls on front panel, tiny little überwachungsrelais

最佳答案

1、电流监控器Currrent Monitor主要特性:
响应时间 / 最大的: 450 ms。
可调节的动作延迟时间。
可调节动作值 电流。
相对的测量精确度 5%.
详见:
https://support.automation.siemens.com/WW/llisapi.dll?func=ll&objId=22935078&nodeid0=20355839&idx0=W&nav0=tree&prodLstObjId=22935078&lang=de&siteid=cseus&aktprim=0&objaction=csviewtd&extranet=standard&viewreg=WW&selectedLang;22935078=1&switchLang;22935078;6.x=1&langex=zh
2、电流监控器Currrent Monitor是一个独立智能型仪表,其特点是精度高、相应快,并且参数可设定。
3、如果对精度高、相应快不要求,可以应用S7-200来实现。如果实现参数可设定,则需配置HMI(触摸屏或上位机)。应用S7-200来实现主要是应用模拟量输入板块来采集电流,根据当前电流值进行相应的动作。
4、有关模拟量的编程:
见《 模拟量输入模块EM231的使用举例》下载:
http://www.ymmfa.com/read-gktid-50415-uid-13129.html
请见《S7-200模拟量输入模块EM231的应用》连接:
http://doc.plcjs.com/doc_jq/SiemensSkill/2008-11/7/0811722230143887.htm
5、建议:还是购置一个新的电流监控器Currrent Monitor吧,这样才能满足当时的设计要求。这种产品上网搜,有的卖。

提问者对于答案的评价:
谢谢

专家置评

已阅,最佳答案正确。

原创文章,作者:more0621,如若转载,请注明出处:https://www.zhaoplc.com/plc302345.html

(0)
打赏 微信扫一扫 微信扫一扫 支付宝扫一扫 支付宝扫一扫
上一篇 2020年10月31日 下午3:00
下一篇 2020年10月31日 下午3:00

相关推荐

  • S-200 上下载

    硬件S-200   cpu 222CN REL 02.01  ,用MICRO WIN&nb…

    SIMATIC S7-200 2020年11月1日
  • 简易位置控制

    我想用200的PLC控制松下的伺服,做简单的位置控制,因为200的PTO输出已经用完,所以想做一个PID将伺服的反馈脉冲读回来作为PV值,然后用模拟量输出控制伺服,在目标位置范围做…

    SIMATIC S7-200 2020年10月31日
  • 如何通过GPRS组网,将几台S7-200的信息集中到控制中心的WICC组态上位机上?

    如何通过GPRS组网,将几台S7-200的信息集中到控制中心的WICC组态上位机上或者控制中心的S7-300上?再通过GPRS向各个200PLC发送命令? 最佳答案 1、请见下述文…

    SIMATIC S7-200 2020年10月31日
  • 网络如何复制啊

    V4.0 STEP 7 MICROWIN SP6 这个编程软件,假如我写了100个网络,我只想复制其中的任意5个网络,应该如何操作…

    SIMATIC S7-200 2020年11月1日
  • S7-200CPU226CN+EM232(32入/32出)X2+EM235X4可否?

    如下组合可否?  S7-200CPU226CN+EM232(32入/32出)X2+EM235X4可否? 问题补充:S7-200CPU226CN+EM232(32…

    SIMATIC S7-200 2021年7月4日
  • 伺服马达转速程序

    我如果采用高速计数器和定时中断来写伺服马达的实际转速程序。会不会不准啊?1:比如我设定的是1S的定时中断,但伺服马达运转还不到1S钟怎么办啊?:2:1S钟的定时中断,假如时间计到0…

    SIMATIC S7-200 2020年11月1日
  • 200modbus 库文件

    200modbus V1.2库文件,目前我有V1.1版本的,求V1.2下载链接,或者发给我,59270150qq.com.V1,1与V1.2有什么区别? 最佳答案 1、S…

    SIMATIC S7-200 2020年10月31日
  • S7200CPU控制伺服电机

    请教各位 用S7200自带高速脉冲Q0.0控制伺服电机(位置控制模式)1 用PLS指令发脉冲控制伺服电机 在编程时使用多段PT0控制 里面有…

    SIMATIC S7-200 2020年11月1日
  • s7200 modbus通讯msg

    我写指令的时候只写了一条msg指令但是一上电就报错6  库存储区也没有占用是为什么外部电脑和plc接的是ip网口 最佳答案 MSG指令报警6#错误是提示你同一周…

    SIMATIC S7-200 2021年7月5日
  • 200CPU的Modbus通讯

    我现在用的是224 XP与变频器485的通讯,现在知道224XP是可以任意一个通讯口都可以实现与RS485设备的通讯 请问:1、200侧的通讯口母口的哪2个针脚…

    SIMATIC S7-200 2020年11月1日